The Air Lift WirelessOne is an advanced on-board air compressor system designed for digital vehicle leveling and suspension adjustment. This system offers a combination of portability, precision, and versatility for vehicle owners seeking enhanced control over their ride height and air pressure settings. The WirelessOne includes both a wireless digital controller and a mobile app, enabling users to manage their air suspension systems from multiple interfaces. This guide is based on the official product documentation and provides a step-by-step breakdown of installation, configuration, and troubleshooting procedures.
Overview of the WirelessOne System
The WirelessOne system includes a manifold, air compressor, wiring harness, wireless digital controller, air line, and integrating hardware. It is compatible with a range of Air Lift suspension products, including the Air Lift 1000, 1000HD, RideControl, and LoadLifter Series. The system is designed for both indoor and outdoor use and features a weather-resistant manifold for extended durability.
The wireless digital controller is a battery-powered unit that allows users to adjust air pressure settings, manage presets, and monitor system performance. Additionally, the mobile app offers remote control capabilities and advanced configuration options, including unit selection (PSI or BAR), compressor or tank mode, and firmware updates.
It is important to note that the WirelessOne system must be configured correctly for optimal performance. The choice between compressor mode and tank mode depends on whether the system is directly connected to the air springs or utilizes an auxiliary tank and solenoid. Incorrect configuration can lead to system errors and reduced performance.
Installation of the WirelessOne System
The installation of the WirelessOne system requires careful attention to wiring and component placement. While the exact installation process may vary depending on the vehicle model and suspension setup, the following steps provide a general overview:
Preparation and Safety Checks
- Ensure the vehicle is turned off and the battery is disconnected before beginning any electrical work.
- Verify that all components included in the kit are present and undamaged.
- Review the installation instructions specific to your vehicle model, as some components may require additional mounting hardware or modifications.
Mounting the Manifold
- The manifold should be mounted in a location that is easily accessible for maintenance and inspection.
- It is recommended to secure the manifold away from direct heat sources to prevent overheating.
- Ensure that the manifold is mounted securely and that all air lines and electrical connections are properly fastened.
Connecting the Compressor
- Connect the compressor to the manifold according to the specified wiring diagram.
- If using an auxiliary tank and external solenoid, connect these components to the manifold and ensure that the system is configured for "Tank Mode."
- In a direct compressor fill setup, the compressor fills the air springs directly, and the system must be configured for "Compressor Mode."
Wiring Harness Installation
- The wiring harness connects the compressor and manifold to the vehicle’s electrical system.
- Follow the wiring diagram provided in the installation manual to ensure correct polarity and secure connections.
- Use high-quality electrical connectors and sealants to prevent corrosion and ensure long-term reliability.
Battery Connections and Grounding
- Connect the system’s positive and negative wires to the vehicle’s battery, ensuring that all connections are secure and properly insulated.
- A dedicated fuse should be installed in the positive wire to protect the system from electrical faults.
- The ground connection should be made to a clean, unpainted metal surface on the vehicle chassis.
Testing the System
- Before fully closing all panels or securing components, test the system to ensure that it powers on and operates correctly.
- Check for any air leaks in the system by listening for hissing sounds and inspecting all fittings.
- If a fitting is leaking at the threads, remove it, apply thread sealant, and reinstall it with 1 1/2 turns beyond finger tight.
Configuration and Pairing with the Wireless Digital Controller
After installation, the WirelessOne system must be configured and paired with the wireless digital controller. This process involves setting up the controller, defining pressure presets, and verifying system performance.
Powering On the Controller
- The wireless digital controller is powered by internal batteries and does not require a separate power source during normal operation.
- Press the inflate and deflate buttons simultaneously to enter the menu interface.
- The factory default unit of measurement is PSI. Users can switch to BAR by selecting the "Units" option in the menu.
Setting Up Presets
- The controller allows for three user-defined presets that can be programmed for frequently used pressure settings.
- To set a preset:
- Adjust the desired pressure using the inflate and deflate buttons.
- Preset 1: Press and hold the P1 button for 3 seconds.
- Preset 2: Press and hold the P2 button for 3 seconds.
- Preset 3: Press and hold both P1 and P2 buttons simultaneously for 3 seconds.
- The controller will indicate which preset is currently selected in the lower left corner of the display.
Verifying System Performance
- Use the controller to inflate or deflate the system and observe the pressure readings.
- The system maintains a minimum air pressure of 5 PSI (.34 BAR) to prevent underinflation.
- If the system fails to respond to commands or displays an error message, refer to the troubleshooting section for possible solutions.
Mobile App Installation and Pairing
The Air Lift WirelessOne app provides an additional layer of control and convenience for users who prefer managing their system from a smartphone or tablet. The app is available for both iOS and Android platforms and can be downloaded from the Apple App Store or Google Play.
Downloading and Installing the App
- Open the Apple App Store or Google Play Store on your device.
- Search for "Air Lift WirelessOne" and select the official app from the Air Lift Company.
- Install the app and open it to begin the pairing process.
Pairing the App with the Manifold
- Put the manifold into pairing mode by removing the fuse for five seconds and reinstalling it. The manifold will remain in pairing mode for three minutes.
- The app will automatically detect the manifold if no previously connected device is detected.
- If multiple devices are in range, select the correct manifold from the list. The manifold will have "WirelessOne" in the title.
- Once paired, the app will connect automatically each time the manifold is active and within Bluetooth range. Only one device can be connected at a time. To connect another device, close the app on the currently connected device.
Managing Presets via the App
- The app allows users to adjust and manage presets in the same way as the wireless controller.
- Presets are stored on the manifold, so changes made in the app will also affect the wireless controller and vice versa.
- To adjust a preset, click on the gear icon next to the preset name.
- Click on the name or pressure value to manually enter a desired pressure and name.
- Click "Accept" to save the preset or "Cancel" to close the preset screen.
Additional App Features
- Pressure Control Units: Users can switch between PSI and BAR in the settings menu.
- Compressor/Tank Mode: Select between compressor mode and tank mode depending on the system setup.
- Prevent Screen Lock: Enable this option to prevent the mobile device from sleeping while the app is open.
- Firmware Update: The app supports firmware updates for the manifold. To update, connect to the internet, open the app, and press "Start." A confirmation will appear before the update begins. Do not close the app or turn off the manifold during this process.
- Online Help: The app includes links to the AirLiftCompany.com website for additional support and documentation.
- About: Displays the app software version and manifold firmware version.
Troubleshooting Common Issues
The WirelessOne system is designed to be reliable, but like any electronic device, it can encounter issues. The following troubleshooting guide outlines common problems and their solutions:
Compressor Doesn’t Run When Inflation Is Commanded
- Error Code 1: Vehicle battery voltage is too low (below 9 volts).
- Solution: Check the vehicle battery and charge or replace it if necessary.
- Error Code 2: Vehicle battery voltage is too high (above 18 volts).
- Solution: Check the vehicle battery and charging system for faults.
- Error Code 3: Manifold temperature is too cold.
- Solution: Allow the manifold to warm up before attempting to inflate.
- Error Code 4: Manifold temperature is too hot.
- Solution: Allow the manifold to cool down. Move it to a location away from heat sources.
- Error Code 14: Compressor under-current.
- Solution: Check battery and ground connections. Disconnect the compressor and test on the bench using 12 volts. Remove and reinstall the 15A fuse to reset the fault.
- Error Code 1: Vehicle battery voltage is too low (below 9 volts).
Bluetooth Connection Issues
- Issue: The app cannot connect to the manifold.
- Solution: Ensure the manifold is in pairing mode. If previously connected to a hand-held remote, turn it off.
- Issue: The app disconnects frequently.
- Solution: Ensure the mobile device is within Bluetooth range of the manifold and that no other devices are interfering with the signal.
- Issue: The app cannot connect to the manifold.
Error Messages in the App
- Active Errors (labeled with "A") and Dormant Errors (labeled with "D") are displayed in the app.
- To clear error codes, use the "CLEAR ERRORS" button in the app.
- Error codes can only be cleared using the mobile app.
General System Errors
- If the system is not functioning correctly and no error codes are displayed, check the following:
- Ensure the system is configured for the correct mode (compressor or tank).
- Verify that all electrical connections are secure and properly insulated.
- Check for air leaks in the system.
- Confirm that the manifold is not overheating or undercooling.
- If the issue persists, contact Air Lift Customer Service for further assistance.
- If the system is not functioning correctly and no error codes are displayed, check the following:
Warranty and Support
The Air Lift WirelessOne system comes with a 2-year limited warranty from the date of purchase, covering defects in materials and workmanship. The warranty is available to the original purchaser and applies to normal use under the conditions specified by Air Lift.
Warranty Registration
- To register the warranty, visit the official Air Lift Company website at https://www.airliftcompany.com/support/warranty/register/.
- Registration helps ensure timely support and service in the event of a warranty claim.
Warranty Claims
- If a warranty claim is necessary, submit it through the official Air Lift website at https://www.airliftcompany.com/support/warranty/submit-claim/.
- Provide the necessary documentation, including proof of purchase and a detailed description of the issue.
Customer Support
- For general inquiries, technical assistance, or replacement parts, contact Air Lift Customer Service at (800) 248-0892.
- Support is also available via email at [email protected].
- If replacement parts are needed, contact a local dealer or call customer service for assistance. Most parts are available for immediate shipment.
Return Policy
- The return policy is subject to the terms outlined in the full Limited Warranty and Return Policy document.
- For complete information, visit https://www.airliftcompany.com/warranty.
Conclusion
The Air Lift WirelessOne is a powerful and flexible on-board air system that offers precise control over vehicle suspension and ride height. With both a wireless digital controller and a mobile app, users can manage their system from multiple interfaces, making it convenient for both on-the-go adjustments and detailed configuration. Proper installation and configuration are essential for optimal performance, and the system includes features such as presets, unit conversion, and firmware updates to enhance usability.
For users encountering issues, the troubleshooting guide and customer support resources provide valuable assistance in resolving common problems. The 2-year limited warranty and return policy further support long-term reliability and customer satisfaction. Whether used for daily driving, off-road adventures, or load hauling, the WirelessOne system is a versatile solution for modern vehicle owners seeking enhanced control and performance.