The installation of Mustang seats generally mirrors the process for original equipment (OE) seats, utilizing existing mounting points and hardware. This guide details the installation procedures for specific motorcycle models, as well as information regarding seat fitment and compatibility, based on provided documentation. Mustang seats are designed to enhance both the comfort and aesthetic of a motorcycle, and are handcrafted in the USA. The documentation emphasizes precision fitment and cautions against mixing Mustang components with stock or aftermarket parts.
Installation Procedures: Yamaha Bolt (2013-2018)
The installation process for a Mustang one-piece seat on a Yamaha Bolt (model years 2013-2018) involves the following steps:
- Insert the ignition key into the left side panel located below the seat.
- Turn the key clockwise and gently pull the panel’s plunger pin out of the body to remove the panel.
- Using a 10mm socket wrench, remove the bolt that secures the forward seat bracket to the frame.
- Lift the nose of the seat and slide it forward to remove the solo seat.
The documentation specifies the need for a 10mm socket wrench for this procedure. Further assistance is available via phone or email, with contact information provided as 800-243-1392 or 413-668-1100, or through the Mustang Seats website at www.mustangseats.com.
Installation Procedures: Harley-Davidson FL Touring (2008-2014)
Installation of a Mustang one-piece seat on a Harley-Davidson FL Touring model (2008-2014) requires these steps:
- Remove the two rearmost Allen bolts from the fender using a 4mm Allen wrench.
- Attach the supplied rear mounting bracket securely to the fender using the stock bolts.
- Slide the Mustang seat back onto the fender, engaging the rear mounting bracket with the fender bracket.
- Lower the nose of the seat into place, allowing the forward seat bracket to drop into the frame receptacle behind the tank.
- Re-install and secure the stock bolt into the frame using a 10mm socket wrench.
- Replace the left side panel and secure it by turning the ignition key counter-clockwise.
The documentation notes a potential issue where the front bracket may not align with the frame mount. In such cases, it is recommended to loosen the fender struts and reposition the fender as high and as far back as the mounts allow.
General Installation Guidelines
The documentation indicates that most Mustang seats are designed for straightforward installation, mirroring the process for removing and installing the stock seat. The typical installation time is approximately fifteen minutes. Detailed “Mounting Suggestions” are included with each seat and are also available on the Mustang Seats website. The documentation also provides contact information for assistance: 800-243-1392 or 413-668-1100, Monday through Friday 9:00 – 5:30 Eastern time, or via email at [email protected].
Measuring Seat Width
Determining the correct seat width is important for ensuring a proper fit. Mustang seats’ width is measured across the widest point of the seating area. This measurement is specific to the rider (“front width”) or passenger (“rear width”). The documentation does not provide specific width measurements for different models.
Compatibility Considerations
Mustang seat components are engineered for precise fitment with each other. The documentation explicitly states that it is generally not possible to mix and match Mustang solo seats and rear seats with stock or other aftermarket components. Prospective buyers are advised to inquire about the fitment compatibility of each individual Mustang solo or rear seat before making a purchase.
Sissy Bar Pad Compatibility
Mustang sissy bar pads are generally compatible with standard size stock sissy bar systems, with very rare exceptions. The documentation does not elaborate on the exceptions.
Seat Care and Maintenance
Information regarding the care and maintenance of Mustang seats is available on the Mustang Seats website under the “Support” section. The documentation does not provide specific details regarding cleaning or conditioning procedures.
Design Philosophy
Mustang Seats emphasizes both rider comfort and aesthetic design. Every seat is meticulously constructed to enhance the lines of the specific motorcycle it is designed for. The company also offers accessories, such as sissy bar pads, tank bibs, and fender bibs, to create a coordinated, custom look.
Conclusion
The installation of Mustang seats is generally a straightforward process, often mirroring the removal and installation of the original equipment seat. Specific procedures vary depending on the motorcycle model. Compatibility between Mustang components and other aftermarket parts is limited, and prospective buyers should verify fitment before purchase. Detailed installation instructions and support resources are available from Mustang Seats, including a website and customer service contact information. The company prioritizes both comfort and the aesthetic integration of its products with the motorcycle’s design.