Mr. Gasket 7668 Universal Floor Shifter Conversion Kit: Installation and Safety Guide

The Mr. Gasket 7668 Universal Floor Shift Conversion Kit is designed for use with automatic transmissions in most rear-wheel drive car applications. This document details the installation instructions, included components, safety precautions, and warranty information associated with this product, as outlined in the provided documentation. The kit aims to convert vehicles to a floor-mounted shifter configuration. Installation requires working under the vehicle and involves modifying the steering column housing.

Kit Contents

The Mr. Gasket 7668 kit includes the following components:

1 Shifter Assembly (Part No. 95090704)
1 Knob (Part No. 97091050)
1 Rubber Boot (Part No. 114 8058)
1 Trim Plate (Part No. 195 2590)
1 Weather-Seal (Plastic Sheet) (Part No. 216 0001)
1 Lever-Extender for Shifter (Part No. 170 0008Z)
1 Rod Adjusting Button (Part No. 119 3783PO)
2 Spring Clips (Part No. 97000015)
1 Cotter Pin (3/32" x 3/4") (Part No. 190 0001)
1 Connecting Rod - Straight (Part No. 213 0011Z)
1 Connecting Rod - Bent (Part No. 213 0012Z)

Safety Precautions

Installation of the Mr. Gasket 7668 requires adherence to specific safety guidelines. The documentation emphasizes performing the installation on a good, clean, and level surface with the engine turned off. Because the installation necessitates working underneath the vehicle, proper lifting and support procedures are critical.

The following safety measures are mandated:

Raise the vehicle using lifting points specified by the vehicle manufacturer.
Secure the vehicle with blocks or wedges placed in front of and behind both rear wheels to prevent movement.
Support the vehicle using approved automotive support stands or wheel ramps.
Do not use a bumper jack for supporting the vehicle.
Exercise extreme care and caution when working underneath the vehicle.
Never position oneself under the vehicle until it is securely supported and stable.

Installation Procedure

The installation process involves mounting an ignition block to the steering column housing. The documentation details two potential mounting locations: above the ignition key switch or below it. The choice of location depends on available space.

The installation steps are as follows:

Determine Mounting Location: Rotate the ignition switch to the “OFF” position. The “OFF” position is identified by feel. Position the Ignition Block so its blade will obstruct rotation of the key switch from “OFF” to “LOCK,” while allowing movement from “OFF” to “ON” and “START.” The blade must extend sufficiently to provide positive obstruction.
Drilling: Hold the Ignition Block in the determined position and use the mounting holes as guides for drilling. A #32 drill bit (0.116” diameter) should be used to drill two holes to a depth of 9/32”. It is crucial not to drill deeper than 9/32”.
Fastening: Fasten the Ignition Block to the column housing using the provided screws. Two different spacers are included: a thin foam spacer for mounting above the key switch and a thicker plastic spacer for mounting below it. The shorter screws are used with the foam spacer, while the longer screws are used with the plastic spacer. The screws are self-tapping and should be installed with slight pressure initially to begin threading, followed by rotation to full depth.
Caution: Avoid over-tightening the screws, as the steering column housing is susceptible to damage.

Ignition Block Operation

After installation, the operation of the ignition key switch is altered slightly. The Ignition Block introduces a deliberate action required to return the key to the “LOCK” position. The key can be turned from “LOCK” to “IGNITION” and “START” without obstruction. However, the blade of the Ignition Block must be retracted before the key can be turned back to “LOCK.” This feature is designed to prevent accidental locking of the steering column while the vehicle is in motion.

Warranty Information

The Mr. Gasket 7668 product is covered by a 90-day limited warranty from the date of purchase. This warranty protects against defects in material and workmanship. During the warranty period, defective products will be repaired or replaced at Mr. Gasket’s discretion.

The warranty does not cover damage caused by:

Misuse
Alteration
Negligence

All implied warranties, including those of fitness and merchantability, are limited in duration to the express warranty period. Mr. Gasket will not be responsible for incidental or consequential damages arising from the installation or use of the product.

Products cataloged for “street” use are not covered by this warranty if used for racing purposes.

Returning Products for Service

To return a product for warranty service, follow these steps:

Pack the product carefully in a sturdy carton with ample padding.
Clearly print the Mr. Gasket address on the carton, along with your return address.
Enclose a letter explaining the nature of the difficulty and include a copy of the sales receipt, your full name, and address.
Attach the envelope containing the letter to the package.
Affix sufficient postage (First Class for the envelope, Parcel Post for the package) and mail the package.

The return address is:

MR. GASKET CO. 10601 Memphis Ave., #12 CLEVELAND, OH 44144 Attention: Technical Service Department

Sources

The provided source material is insufficient to produce a 2000-word article. Below is a factual summary based on available data.