The Moen Darcy Y1518 series towel bar is available in 18-inch and 24-inch lengths, offered in both chrome and brushed nickel finishes. Constructed from zinc, the towel bar requires specific tools for installation and includes a hardware kit containing anchors and a hex wrench. Installation procedures differ slightly depending on whether the mounting is to drywall or a stud. Proper cleaning procedures are also outlined to maintain the product’s finish. This article details the specifications, installation process, and maintenance guidelines for the Moen Darcy Y1518 series towel bar, based on the provided documentation.
Product Specifications
The Moen Darcy towel bar is manufactured in two length options: 18 inches and 24 inches. These are identified by the stock numbers Y1518CH, Y1518BN, Y1524CH, and Y1524BN. The “CH” designation indicates a chrome finish, while “BN” denotes a brushed nickel finish. The towel bar is constructed of zinc. The documentation does not provide weight specifications or load-bearing capacity.
Installation Procedure
Installation of the Moen Darcy towel bar requires a Phillips screwdriver, a drill, a 1/4-inch drill bit, a hammer, a level, and tape. The hardware kit includes two anchors and one hex wrench. The installation process varies based on the wall material. The provided instructions specifically address installation into drywall and into a stud.
Installation into Drywall
The following steps are to be followed when installing the towel bar into drywall:
- Remove the mounting posts from the product assemblies by loosening the setscrews.
- Position the mounting plate on the wall in the desired location and mark the hole locations using the template, specifically noting the horizontal screw locations for drywall installation.
- Drill 1/4-inch pilot holes at the marked locations.
- Lightly tap the anchors into the drilled holes until they are flush with the wall surface.
- Place the mounting plate over the anchors and insert screws through the post into the anchors.
- Tighten the screws to secure the mounting plate.
- Place the posts over the mounting plates, ensuring the setscrew faces downward, and tighten the setscrew.
Installation into a Stud
When installing into a stud, the instructions indicate that only the wood screws should be used. The documentation does not provide specific instructions for locating studs or the appropriate screw size for wood installation. The initial steps of removing mounting posts and positioning the mounting plate remain the same, but the marking of holes should focus on the vertical screw location for stud installation. Drilling pilot holes and securing the mounting plate with screws are also required.
Hardware Kit Contents
The hardware kit provided with the Moen Darcy towel bar contains the following components:
- Two anchors
- One hex wrench
The documentation does not specify the material composition of the anchors or the size of the hex wrench. It is implied that additional screws are included, but the specific type and quantity are not detailed.
Cleaning and Maintenance
To preserve the finish of the Moen Darcy towel bar, the documentation recommends cleaning only with a soft, damp cloth. Users should dry the towel bar thoroughly after cleaning. The use of commercial or abrasive cleaners is explicitly prohibited, as these may damage the finish. The documentation does not provide guidance on removing specific types of stains or restoring a tarnished finish.
Contact Information
Moen Incorporated provides several avenues for customer service and technical support. The corporate headquarters can be reached at (800) 321-8809, with a fax number of (800) 848-6636. International inquiries can be directed to (440) 962-2000, with a fax number of (440) 962-2726. U.S. customer service is available at 800-882-0116, with a fax number of (888) 379-2720. The company website is www.moen.com.
Copyright Information
The documentation indicates that Moen is a registered trademark and Darcy is a trademark of Moen Incorporated. The document is copyrighted by Moen Incorporated in 2015, and all rights are reserved. The corporate address listed is 25300 Almond Drive, North Olmsted, OH 44070.
Conclusion
The Moen Darcy Y1518 series towel bar is a zinc-constructed bathroom accessory available in multiple finishes and lengths. Installation requires basic tools and adherence to specific procedures depending on the wall type. Maintaining the product’s finish involves regular cleaning with a soft cloth and avoiding abrasive cleaners. The provided documentation offers contact information for customer support and clarifies the product’s trademark and copyright status.