Installing a Good Health Saunas infrared sauna is presented as a straightforward process, suitable for individuals comfortable with basic assembly tasks. The provided documentation details step-by-step instructions for several models, including 2-person, 3-person, and corner configurations, across both Signature and Hybrid series. The installation process generally involves assembling panels, securing buckles, connecting wiring, and finally, plugging the unit into a standard wall outlet.
Initial Setup and Location
The first step in installing a Good Health Saunas infrared sauna involves selecting a suitable location and placing the base of the unit on the floor. The documentation emphasizes choosing a location where the sauna can be enjoyed. No specific environmental requirements (e.g., temperature, humidity, flooring type) are detailed in the provided materials.
Panel Assembly – General Procedure
A common thread throughout the installation procedures for all models is the assembly of panels. This typically begins with inserting the back panel onto the base, requiring assistance to hold it in place while a side panel is inserted. Window panels (left and right) are then added, ensuring that the “tongs and grooves” are securely interlocked. Fastening the outside buckles secures these panels. The documentation consistently stresses the importance of ensuring panels are well inserted into one another.
Bench Installation
Bench installation varies slightly between models. For 2-person saunas, both lower and upper bench parts are slid into place and secured. In some models, connecting wires are present and must be secured during this step. The 3-person models also involve sliding the bench panel into place, ensuring a secure fit.
Front Window and Buckle Fastening
The front window panel is installed by aligning the “tongs and grooves,” with the unfinished side facing inward and the finished side facing outward. Following the window panel installation, the remaining buckles are fastened to complete the structural assembly of the sauna.
Wiring and Component Installation
Several models, particularly the Hybrid series, require additional wiring steps. The Bench Heater Cable is plugged into an outlet located on the Back Panel, and the connection must be secure. Stereo and ionizer installation are also detailed in some instructions. The stereo requires insertion into a mounting box before connecting wires. The round wire is identified as the stereo antenna and plugs into a corresponding opening on the back of the stereo unit. The ionizer connects to a black wire from the ceiling near the side panel. A dust cover is then attached with short screws.
Roof Installation and Cable Management
Prior to roof installation, the documentation advises checking all cables and pushing them aside to prevent damage to the wiring terminals. Plugs for the heater are pushed through holes around the top panel and then connected. Proper alignment of the roof is emphasized during installation. For some models, the control panel also requires connection via flat connector wires.
Final Steps and Power Connection
The final step across all models is plugging the sauna into a wall outlet. The documentation consistently states that once plugged in, the sauna is ready for use.
Model-Specific Installation Details
While the general procedure remains consistent, some variations exist between models.
2-Person Saunas (Signature Series)
The installation for the 2-person Signature Series sauna follows the general panel assembly procedure outlined above. Steps include choosing a location, inserting the back and side panels, installing window panels, fastening buckles, sliding in the bench parts, and finally, plugging the unit into a wall outlet.
2-Person Saunas (Hybrid Series)
The 2-person Hybrid Series installation is similar to the Signature Series, with the addition of securing wires during bench installation.
3-Person Saunas (Signature & Hybrid Series)
The 3-person Signature and Hybrid Series installations share a common initial sequence: placing the bottom panel, installing the back panel, and then the side panels. The Hybrid series includes the additional step of installing the Bench Heater Panel and connecting its cable to the outlet on the Back Panel.
3-Person Corner Saunas (Hybrid & Signature Series)
The installation of the 3-person corner saunas follows a similar pattern to the other models, with the emphasis on aligning panels and securing buckles. The Hybrid series includes the same wiring steps as the 3-person Hybrid sauna, including stereo and ionizer installation.
Important Considerations During Installation
The documentation highlights several important considerations during installation:
- Secure Panel Connections: Ensuring that “tongs and grooves” are well inserted into one another is repeatedly emphasized.
- Buckle Fastening: Properly fastening all buckles is crucial for structural integrity.
- Cable Management: Careful attention to cable management, particularly before roof installation, is advised to prevent damage to wiring terminals.
- Wiring Security: All wire connections must be secure.
- Component Orientation: The front window panel must be installed with the unfinished side facing inward and the finished side facing outward.
- Roof Alignment: The roof must be well aligned during installation.
Conclusion
The installation of Good Health Saunas infrared saunas, as detailed in the provided documentation, appears to be a manageable process involving panel assembly, wiring connections (for certain models), and a final power connection. The instructions emphasize secure panel connections, proper cable management, and attention to detail throughout the process. The documentation provides specific guidance for various models, including 2-person, 3-person, and corner configurations, across both Signature and Hybrid series.