The Dannmar MaxJax Tilt is a portable, low-rise tilting lift designed for use on unibody construction vehicles. It offers a maximum lifting capacity of 6,600 pounds, though some documentation references 6,000 pounds. The lift is intended for indoor and outdoor use, but should not be installed in a pit or depression. Proper installation and adherence to safety instructions are critical to prevent bodily harm and maintain product warranty. This article details the installation process, operational guidelines, and technical specifications based on available documentation.
Unpacking and Component Identification
Upon receiving the MaxJax Tilt, the shipping container should be inspected for damage. The container is opened by prying open close tabs around the crate. Verification of all components is necessary, referencing the Component Parts Identifier list. Components included are the MaxJax Tilt Frame, Jack Support Stand, Frame Platforms (2), Risers (2), Frame Connecting Sleeves, Bolts, Washers, and Nuts. A Safety Jack Stand, Parts Bag, Drill Drive Adapter, Positioning Wheels, and associated screws and nuts are also included. Optional components, such as Track Rails, are available separately.
Assembly Procedure
The assembly of the MaxJax Tilt involves several steps. Initially, the Arms should be raised so that the holes at the top align. Applying lithium grease to the interior of these holes facilitates easier component travel. Frame Connecting Sleeves, Bolts, Washers, and Nuts are then inserted into the Frame. Platforms are slid onto the Sleeves and secured with Bolts. This process is duplicated for the opposite set of Arms.
Next, the Mainframe is flipped over, and the Positioning Wheels are attached. Once these steps are completed, the assembly is considered complete. Before initial use, it is recommended to add additional grease to the Gear Drive Boxes (one per side) using a lubricant such as Valvoline NLGI #2 GC-LB Complex Lithium EP Grease. This reduces friction within the gears and screw drive. It is normal to observe grease on the side drive shaft, and excess grease should be wiped down after each use.
Installation Requirements and Site Selection
The MaxJax Tilt requires a smooth and flat surface for operation. Installation should occur in an indoor location, as specified in some documentation. The documentation specifies a floor/surface that is as smooth and flat as possible. The lift has specific mechanical requirements detailed in the Installation Instructions. When installing, users should consider the vehicle’s frame chassis width, which must be between 48 and 61 inches.
Installation may require concrete fasteners meeting the criteria of the ANSI/ALI ALIOM safety requirements. The documentation emphasizes the importance of following installation instructions to avoid personal injury or damage to the lift.
Operational Guidelines
Prior to using the MaxJax Tilt, the vehicle must be in Park with the Emergency Brake engaged. The lift is then rolled under the vehicle, positioned closest to the front wheels. The Platforms are aligned under the chassis frame rails. If pinch welds or body cladding interfere with the Platform surface, Riser Bars should be placed on the Platforms before raising the vehicle.
To operate the lift, a Drill Drive Adapter is inserted into a drill and then into the Gear Box. After the drill is inserted, the lift is lowered to the ground. Once lowered, the lift is ready for use under the vehicle.
Technical Specifications
The MaxJax Tilt has the following documented technical specifications:
- Lift Capacity: 6,600 pounds (maximum), with some documentation referencing 6,000 pounds.
- Dimensions: 1635 x 1300 x 115 mm (approximately 64-1/2” x 51-1/4” x 4-1/2”).
- Weight: 45 kg / 99 lbs.
- Height Capacity: 60 cm / 23-1/2”.
- Lift Speed: 30-40 seconds (dependent on drill amperage and vehicle weight).
- Platform Width/Length: 184.15mm X 800mm / 7-1/4" X 31-1/2".
- Maximum Outside Width of Platform: 1638mm / 64".
- Minimum Outside Width of Platform: 1270mm / 50".
The documentation explicitly states that an impact drill should not be used with this lift.
Safety Precautions and Warnings
Several safety precautions are outlined in the provided documentation. Users are instructed to read the entire manual before installation and operation. The lift is designed for indoor/outdoor use and should not be installed in a pit or depression. When not in use, it should be stored in a cool, dry interior space.
The documentation emphasizes the importance of understanding hazard levels and following all danger, warning, and caution instructions to prevent serious personal injury or death. It also warns against modifying components without consulting Dannmar Equipment for certified attachments and accessories. Maintaining a clean work area and avoiding operation in damp or wet locations are also recommended.
Optional Accessories
Dannmar Equipment offers optional accessories for the MaxJax Tilt, including a Motorcycle ATV Adapter Kit, an RD-9G Upright Oil Drain, a RST-1WS Rolling Work Seat, an Epoxy Anchor Bolt Kit, Frame Cradle Pads, a Standard Anchor Bolt Kit, and Stackable Height Adapters.
Troubleshooting
The provided documentation does not contain a detailed troubleshooting guide. However, it directs users to contact Dannmar Equipment for assistance with any issues.
Conclusion
The Dannmar MaxJax Tilt is a portable lifting solution designed for vehicle maintenance. Proper installation, adherence to safety guidelines, and understanding of the lift’s technical specifications are crucial for safe and effective operation. The lift’s capacity, dimensions, and operational requirements make it suitable for a range of automotive tasks, provided the vehicle’s frame width falls within the specified range. Users should consult the full user manual for comprehensive instructions and safety information.