The Lund Latitude 26510017 nerf bar kit is designed for installation on F-150 Super Cab vehicles. The documentation details the components included in the kit, necessary tools, preparation steps, and important safety information. This article provides a comprehensive overview of the installation process and safety precautions based solely on the provided installation instructions.
Kit Contents
The Lund Latitude 26510017 nerf bar kit includes the following components:
- Passenger Side Nerf Bar
- Driver Side Nerf Bar
- Passenger Front Bracket
- Passenger Mid Bracket
- Passenger Rear Bracket
- Driver Front Bracket
- Driver Mid Bracket
- Driver Rear Bracket
- 12mm Single Bolt
- 12mm Double Bolt
- 12mm Plastic Plate (2)
- Retainers (8)
- 12mm hex nuts (6)
- 8mm Lock Washer (20)
- 12mm flange nut (2)
- 8mm x 30 mm hex bolt (8)
- 8mm x 24mm hex bolt (8)
- OD x 2mm Flat Washer (24)
- 8mm x 25 mm Washer Plate hex bolt (12)
- 8mm clip nuts (4)
- 8mm Hex Nut (4)
- Wheel Chocks
- Socket Set
The documentation notes that the actual product may vary from the illustration.
Required Tools
The installation of the Lund Latitude 26510017 nerf bar kit requires the following tools:
- Ratchet and Extension
- Safety Glasses
The documentation emphasizes the importance of reading and understanding all operating instructions when using power tools.
Preparation Before Installation
Prior to beginning the installation process, the following preparatory steps must be taken:
- Park the vehicle in a clean, level location.
- Ensure the vehicle is in park (for automatic transmissions) or first gear (for manual transmissions).
- Engage the parking brake.
- Chock the wheels.
- Unpack the kit and identify all parts according to the content descriptions.
- An assistant is recommended to help position the running board properly during installation.
Installation Instructions
The provided documentation focuses on general installation instructions and component identification. Specific step-by-step guidance for attaching the brackets and nerf bars to the vehicle frame is not included in the available source material. The instructions emphasize the importance of reading all instructions before beginning the installation process to ensure a proper fit. The instructions refer to both passenger and driver side components, indicating a symmetrical installation process for both sides of the vehicle.
Safety Information
The documentation includes several important safety warnings:
- The nerf bars and brackets should not be used as a jacking point for the vehicle.
- The bracket system or running boards should not be used to fasten cargo.
- All components should be periodically checked for tightness.
- Safety glasses must be worn during bracket installation.
- The product is to be used with Lund® branded products only.
- Users should not stand on the Lund running board or bracket while the vehicle is in motion.
Component Specifics
The kit includes various types of bolts, washers, and nuts. These include:
- 12mm Single Bolt
- 12mm Double Bolt
- 8mm x 30 mm hex bolt
- 8mm x 24mm hex bolt
- 8mm x 25 mm Washer Plate hex bolt
- 12mm hex nuts
- 12mm flange nut
- 8mm clip nuts
- 8mm Hex Nut
- 12mm Lock Washer
- 8mm Lock Washer
- OD x 2mm Flat Washer
- 12mm Plastic Plate
- Retainers
The documentation lists quantities for each of these components, allowing for verification of kit completeness before installation.
Technical Assistance
For technical assistance or to obtain missing parts, customers can contact Customer Relations at 1-800-241-7219.
Conclusion
The Lund Latitude 26510017 nerf bar kit provides components for installing running boards on an F-150 Super Cab. Proper installation requires careful preparation, including vehicle stabilization and component identification. Adherence to the provided safety warnings is crucial to prevent injury and ensure the longevity of the product. The documentation emphasizes the importance of reviewing all instructions before beginning the installation process and provides a contact number for technical support.