This article provides a detailed, step-by-step guide for the installation of the Allen Roth LED flushmount ceiling fixture, based on the official manufacturer documentation and user support resources provided. It is designed for U.S. consumers, DIY enthusiasts, and homeowners who want to install a flushmount ceiling light safely and correctly. The instructions cover preparation, assembly, wiring, and troubleshooting, with a focus on safety and compliance with electrical codes.
Introduction
The Allen Roth LED flushmount ceiling fixture is a modern lighting solution designed for installation in standard ceiling boxes. It is available in two models: the LBX8002AX-01 and the CLL14CH, both of which are compatible with LED or equivalent lighting sources and require no incandescent bulbs. The installation process is straightforward but must be approached with care to ensure electrical safety and proper function.
The documentation provided outlines key installation procedures, including wiring, mounting, and safety precautions. It also includes troubleshooting guidance for common issues such as non-functioning bulbs or tripped circuit breakers. This article compiles and clarifies these instructions to provide a comprehensive resource for users.
Preparation and Safety
Before beginning the installation of the Allen Roth LED flushmount ceiling fixture, it is essential to ensure that all safety precautions are followed. The manufacturer explicitly states in its instructions that the user must turn off the main power supply to the circuit before working on the fixture. This is a critical step to prevent the risk of electrical shock.
In addition, the documentation emphasizes the importance of using appropriate personal protective equipment, such as gloves, to avoid cuts from sharp metal edges on the fixture components. It is also recommended to use a flashlight or an alternate light source during installation to maintain visibility in dimly lit work areas.
Tools and Materials
The following tools and materials are required for the installation process, though they are not included with the fixture:
- Pliers
- Screwdrivers (for tightening screws)
- Electrical tape
- Damp cloth (for cleaning after installation)
- Flashlight or alternate light source
The fixture itself comes with all necessary hardware, including mounting screws, a mounting strap, and pre-assembled components such as the shade and fixture body.
Pre-Installation Check
Prior to starting the installation, users should verify that all components are present and undamaged. This includes the fixture body, mounting hardware, and any pre-assembled parts. If any part is missing or damaged, installation should not proceed until the issue is resolved.
The estimated assembly time for both the LBX8002AX-01 and CLL14CH models is 20–30 minutes, assuming that the user is familiar with basic electrical installation procedures.
Step-by-Step Installation Instructions
Step 1: Turn Off the Power Supply
Before beginning any electrical work, the user must turn off the power supply to the circuit at the main electrical panel. This is a critical safety step and should be confirmed by testing the existing wiring with a voltage tester if available. The manufacturer explicitly warns that failure to do so can result in electrical shock or other injuries.
Step 2: Mounting the Fixture
The fixture is mounted using a mounting strip (A) and a set of screws. The process involves the following steps:
- Attach the mounting strip (A) to the outlet box using two short mounting screws (AA).
- Feed the wires through the fixture, ensuring that black wires are connected to black wires, white wires to white wires, and ground (bare) wires to ground connections.
- Twist the stripped wire ends together using pliers and secure them with electrical tape.
- Place the ceiling plate (C) over the outlet box and align the long mounting screws (B) with the keyhole slots.
- Tighten the long mounting screws (B) to secure the ceiling plate in place.
For the CLL14CH model, the shade is pre-assembled with the fixture. After mounting the fixture, the shade can be attached using the included screws (C).
Step 3: Wiring the Fixture
The wiring process for both models follows a standard procedure:
- Black (hot) wires are connected to black fixture wires.
- White (neutral) wires are connected to white fixture wires.
- Ground (bare) wires are connected to ground connections.
The manufacturer emphasizes that these connections must be secure and properly insulated with electrical tape. After the connections are made, any excess wiring should be carefully pushed into the outlet box to prevent strain on the connections.
The documentation also warns that the fixture should not be supported by the house wires alone, as this can lead to the fixture falling and cause injury or damage. Instead, the mounting hardware should bear the weight of the fixture.
Step 4: Final Assembly and Testing
Once the fixture is mounted and wired, the final steps include:
- Installing the glass shade (E) for the LBX8002AX-01 model.
- Securing the shade with three thumb screws (D).
- Ensuring that all screws are properly tightened and that the fixture is stable.
- Restoring power to the circuit.
- Testing the fixture to confirm that it is functioning correctly.
If the fixture does not light up, the troubleshooting section of the manual should be consulted.
Safety and Compliance Considerations
The manufacturer provides several important safety and compliance reminders:
- The fixture is rated for use with 60-watt maximum standard-base incandescent bulbs or equivalent LED/CFL bulbs. Exceeding this wattage can lead to overheating and potential fire hazards.
- The fixture is designed to accept only one 12-gauge house wire and two lead wires from the fixture. If the house wiring is larger than 12-gauge or if there is more than one house wire to connect, the user should consult a licensed electrician.
- If the fixture is to be used on a dimming circuit, the user must use a dimmable LED bulb and obtain professional advice to determine the appropriate type of dimmer switch.
- The fixture must be grounded, and the user should ensure that the electrical system provides a proper grounding means. If there is any doubt about the grounding system, a qualified electrician should be consulted.
The manufacturer also notes that the fixture must be mounted to an outlet box that is supported by the building structure. Using an unsupported outlet box can result in the fixture falling, which poses a risk of personal injury and electrical hazards.
Troubleshooting Common Issues
The manual includes a troubleshooting section that addresses several common problems and their solutions:
Problem: Bulb will not light.
Possible Causes:- Burned-out bulb
- Faulty wire connection
Corrective Actions: - Replace the bulb
- Check the wiring and connections
Problem: Light does not come on initially or no longer comes on.
Possible Causes:- Power is off
- Faulty connection
- LED component failure
Corrective Actions: - Ensure the power is on
- Check wiring and connections
- Contact customer service
Problem: Fuse blows out or circuit breaker trips.
Possible Causes:- Crossed wires
- Power wire grounding out
Corrective Actions: - Check the wiring
- Inspect all connections
If the user is unable to resolve the issue using the troubleshooting guide, they are advised to contact customer service at 866-439-9800 or via email at [email protected].
Care and Maintenance
After installation, the fixture should be cleaned with a soft, damp cloth. The user should ensure that the main power is turned off before cleaning. Abrasive cleaners should not be used, as they can damage the finish of the fixture.
The LED component of the fixture is not user-replaceable. If the LED fails, the user should contact customer service for assistance.
Warranty Information
The warranty information varies slightly between the two models:
- LBX8002AX-01: The manufacturer offers a one (1) year limited warranty against defects in materials and workmanship from the date of purchase.
- CLL14CH: The distributor offers a five (5) year warranty from the date of purchase.
In both cases, the warranty covers defects in materials and workmanship but does not cover damage caused by misuse, improper installation, or accidental damage. The user is responsible for the cost of installation and removal of the fixture. Additionally, the warranty does not cover incidental or consequential damages.
If a defect is discovered within the warranty period, the user should present a copy of the bill of sale and the product in its original packaging to the place of purchase. The distributor will then repair, replace, or refund the purchase price, at its discretion.
Conclusion
The Allen Roth LED flushmount ceiling fixture is a versatile and efficient lighting solution suitable for a variety of residential applications. Installation can be completed in approximately 20–30 minutes by following the detailed instructions provided in the manufacturer’s documentation. However, it is essential that users approach the installation with care and follow all safety precautions to avoid injury or damage.
For users who are unfamiliar with electrical work or who encounter difficulties during installation, it is recommended to consult a licensed electrician. The manufacturer also provides a customer service line for assistance with troubleshooting and warranty-related inquiries.
By adhering to the instructions and safety guidelines outlined in this article, users can ensure a safe and successful installation of their Allen Roth LED flushmount ceiling fixture.