Hudson Reed radiators require careful installation to ensure optimal performance and safety. These guidelines, based on available documentation, cover product information, installation procedures, safety requirements, and post-installation care. The information provided is intended for qualified plumbers or competent individuals familiar with central heating systems.
Product Specifications and Safety Information
Hudson Reed radiators are designed for use on indirect or sealed central heating systems, including combi boilers. The radiators are constructed from steel and are suitable for use with water/glycol mixtures. It is crucial that the operating pressure does not exceed 1 MPa (10 g/cm², 10 Bar, 145 PSI). The maximum operating temperature should remain below 100 °C (212°F).
A critical safety consideration is temperature control. If the surface temperature of the radiator exceeds 48 °C (120 °F), a warning sign must be displayed nearby to prevent burning and scalding accidents. The documentation emphasizes the importance of adhering to local water regulatory byelaws during installation.
Installation Procedures
Prior to installation, it is recommended to verify that all included parts are present. Installation requires specific tools, including a 10mm wrench and 1/2" inlet/outlet tools. The installation process involves several key steps:
- Center Line Marking: Begin by accurately marking the center line of the radiator on the wall.
- Valve Preparation: Apply PTFE tape to the tail of each radiator valve.
- Valve Installation: Screw the valves onto the radiator, ensuring a secure fit. Remove the radiator bung during this process.
- Air Vent Installation: Carefully screw in the air vents, avoiding over-tightening to prevent damage to the O-ring.
- Wall Mounting: Utilize the provided wall fixings, which are specifically designed for solid brick walls. If installing on a different surface, it is essential to verify the suitability of the fixings.
- Heating Element Installation (Electric-Only Radiators): If installing an electric-only radiator, the heating element must be installed at the bottom of the radiator, perpendicular to the pipes, allowing for proper heating medium circulation. This step should only be performed by a qualified installer.
Safety Requirements During Installation
Several safety precautions must be observed during installation:
- Wear appropriate personal protective equipment, including safety boots and gloves.
- Fitting and connection of the heating element (if applicable) should only be carried out by a qualified installer.
- Switching on the heating element in open air for testing is permitted for a maximum of 3 seconds only.
- Ensure the electrical installation is sound and meets the heater’s rating specifications.
Heat Output Measurement
Radiator heat output is measured in either British Thermal Units (BTUs) or Watts. It is advisable to choose a radiator with a slightly higher heat output than required, as the output can be adjusted downwards. A qualified installer should calculate the BTU requirement for each room to maximize heating efficiency.
Post-Installation Care and Recycling
After installation, it is important to recycle the packaging materials in accordance with local government regulations. The same practice should be followed at the end of the product’s life. The radiators are designed for minimal maintenance, but regular bleeding of air vents may be necessary to maintain optimal performance.
Product Range and Components
Hudson Reed offers a variety of radiator components and accessories, including:
- Chrome temperature body sleeve
- Angled Thermostatic Radiator Valve Pack
- Straight Radiator Valve Pack (Pairs)
- Shower Tidies
- Riser Rails
General Information and Guarantee
Hudson Reed radiators are manufactured from steel and packaged in cardboard, plastic, and steel. The company provides a guarantee on its products, details of which can be found in the accompanying documentation.
Contact Information
For questions or free estimates, contact Hudson Reed at the following locations:
- Lutz: 813-948-9091
- Land O Lakes: 813-345-8596
- New Tampa: 813-632-0050
- General Inquiries: 1-877-778-8460
- Address: Unit 1&2 Dawson Ct, Burnley BB11 5UG
Conclusion
Proper installation of Hudson Reed radiators is essential for safe and efficient operation. The provided documentation emphasizes the importance of qualified installation, adherence to safety guidelines, and compliance with local regulations. By following these instructions, consumers can ensure optimal performance and longevity of their heating systems.