For U.S. consumers seeking reliable, energy-efficient outdoor and indoor lighting solutions, Good Earth Lighting offers a range of LED products tailored for both aesthetic and functional purposes. From hyper-bright floodlights ideal for security to smart LED flat panel and strip lights for ambient control, these products integrate modern technology with straightforward installation procedures. This article provides a detailed, step-by-step guide to installing and configuring Good Earth LED lighting solutions, focusing on best practices, safety measures, and compatibility information.
Installation Overview and Key Considerations
Good Earth Lighting’s LED products are designed to simplify installation while ensuring durability and performance. The following considerations apply across all models:
- Power Safety: Always turn off the power at the circuit breaker or fuse panel before beginning any installation to prevent electrical hazards.
- Mounting Height: For optimal performance, especially with motion-sensor floodlights, mount the fixture at a height between 8 and 10 feet.
- Avoid Interference: Install the light away from other light sources such as streetlights or traffic signals to prevent sensor interference.
- Grounding: Ensure all fixtures are properly grounded to prevent electrical faults.
- Environmental Protection: Use provided gaskets or sealants to prevent water ingress, especially for outdoor models.
- Compatibility: Verify that your electrical setup supports the model you are installing, and consult the manual for dimmer compatibility if applicable.
Installing the SE1356-WH3-02LF4-G Hyper Bright LED Flood Light
The SE1356-WH3-02LF4-G Hyper Bright LED Flood Light is a high-performance outdoor fixture with a reflector LED for enhanced brightness. This model is ideal for security lighting and features a motion sensor for automatic activation.
Tools and Materials Required
- Step ladder
- Silicone sealant
- Hammer
- Seal
- Phillips head screwdriver
- Surface mount electrical box (if required)
- Foam gasket (included for waterproofing)
Step-by-Step Installation
- Preparation: Turn off the power at the circuit breaker. Remove the existing fixture if replacing it.
- Mounting Location: Choose a location that allows the sensor to operate at peak efficiency. The recommended height is between 8 and 10 feet.
- Mounting Box: If using a surface mount electrical box, apply the included foam gasket to prevent water seepage.
- Fixtures and Wiring: Secure the fixture using the provided tools. Ensure all wiring connections are tight and secure.
- Sensor Adjustment: Use the Time Duration Control Dial and Detection Range Control Dial to adjust the sensor’s sensitivity and activation time.
- Power Restoration: Turn the power back on at the circuit breaker. Test the light to ensure it functions correctly and adjust the settings as needed.
- Warranty and Support: The fixture comes with a 10-year limited warranty. For technical support, contact Good Earth Lighting at 1-800-291-8838.
Connecting Good Earth LED Lights to a Smart App
For models that support smart connectivity, users can integrate their Good Earth LED lights with a smartphone app to enable remote control and automation. This feature is especially useful for managing indoor lighting environments.
Prerequisites for Smart Connectivity
- A smartphone with the Good Earth Lighting app installed
- A stable Wi-Fi network
- A compatible light fixture (e.g., smart LED flat panel or strip lights)
- The light fixture must be connected to a power source and secured according to the manufacturer’s instructions
Pairing the Light with the App
Entering Pairing Mode:
- For most models, press and hold the pairing button on the fixture for six seconds until it begins blinking rapidly.
- For other models, power cycle the light (turn it off and back on) three times within a few seconds.
App Setup:
- Open the Good Earth Lighting app and navigate to the device setup section.
- Select “Add Device” and choose your specific model from the list.
- The app will prompt you to connect to your Wi-Fi network. Enter your network password accurately to avoid connection issues.
Post-Installation Testing:
- After pairing, test the app controls to ensure the light responds to commands.
- Adjust brightness, color temperature, or scheduling as needed.
Installing Smart LED Flat Panel and Strip Lights
Good Earth Lighting also offers smart LED flat panel and strip lights, which are ideal for modern interiors and flexible lighting setups.
Smart LED Flat Panel Lights
These flat panel lights are designed for ceiling installations and provide uniform, bright illumination without the bulk of traditional fixtures. They are compatible with smart home systems like Amazon Alexa and Google Assistant.
Installation Steps:
- Mounting: Secure the flat panel light according to the manufacturer’s instructions. Ensure it is level and properly attached to the ceiling.
- Wiring: Connect the wiring as specified in the manual. Ensure all connections are secure and grounded.
- Power Testing: Restore power and verify that the light functions as expected. Adjust brightness and color settings via the app if supported.
Integration with Smart Assistants:
- After installation, connect the light to the Good Earth Lighting app and link it to your preferred smart assistant.
- Voice commands can then be used to control the light, including adjusting brightness, changing color temperature, or setting schedules.
LED Strip Lights
Good Earth’s LED strip lights are versatile and can be used for under-cabinet lighting, stair lighting, or accent lighting in living spaces.
Installation Steps
Measurement and Cutting:
- Use a measuring tape to determine the required length of the strip.
- Most LED strips can be cut at designated points marked along the strip. Use sharp scissors to make clean cuts.
Surface Preparation:
- Clean the surface where the strip will be installed to remove dust or grease. A clean surface ensures better adhesion.
- Use rubbing alcohol and a cloth for thorough cleaning.
Installation:
- Peel off the adhesive backing and carefully place the strip on the marked area.
- Press firmly to ensure adhesion. Consider using mounting clips for added stability in high-traffic areas.
Wiring and Power:
- Connect the strip to a power source, following the manufacturer’s wiring instructions.
- Secure all connections and restore power to test the strip.
Smart Functionality (If Applicable):
- If the strip supports smart connectivity, follow the app pairing instructions as outlined in the previous section.
Troubleshooting and Common Issues
Despite careful installation, users may encounter issues with their Good Earth LED lights. The following troubleshooting tips are based on information from official support documentation and user queries.
Dim or Inconsistent Light Output
- Possible Cause: Faulty wiring, damaged components, or an incompatible dimmer.
- Solution:
- Ensure all connections are secure and undamaged.
- Check for compatibility if using a dimmer. Refer to the list of recommended dimmers in the manual.
- Contact customer support at 1-800-291-8838 for further assistance.
Sensor Not Activating
- Possible Cause: Incorrect mounting height or sensor interference.
- Solution:
- Adjust the mounting height to between 8 and 10 feet.
- Ensure the sensor is not obstructed and is away from other light sources.
App Connection Issues
- Possible Cause: Incorrect Wi-Fi password, weak signal, or outdated firmware.
- Solution:
- Re-enter the Wi-Fi password carefully.
- Ensure the router is within range of the light fixture.
- Check for firmware updates in the app or on the manufacturer’s website.
Compatibility and Recommended Accessories
Good Earth Lighting provides compatibility information for various components to ensure optimal performance.
Dimmer Compatibility
The SE1356-WH3-02LF4-G and other dimmable models are compatible with specific forward-phase electronic (TRIAC) dimmers. The following dimmers have been tested and approved for use:
- Lutron Skylark SCL-153P
- Lutron Diva DVCL-153P
- Lutron Maestro MACL-153M
- Lutron Toggler TGCL-153P
- Lutron Lumea LECL-153P
- Lutron Caseta PD-6WCL
- Eaton Halo SAL06P
These dimmers are recommended for use with the fixtures. Avoid using motion sensors, light sensors, timers, or other external controls, as they may interfere with the operation of the LED lights.
Replacement Parts and Accessories
Good Earth Lighting offers replacement parts for certain models. For the SE1356-WH3-02LF4-G, the following hardware kits are available:
- ZH-SE1356-F01-WH3
- ZH-SE1356-F01-BP2
For replacement parts and technical support, contact Good Earth Lighting at 1-800-291-8838 or visit their website.
Safety and Regulatory Compliance
All Good Earth LED lighting products comply with FCC regulations and are designed to minimize interference with radio and television reception. In the event of interference, users are advised to take the following steps:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a different circuit than the receiver.
- Consult a qualified technician or dealer for further assistance.
The FCC responsible party for these products is Good Earth Lighting Inc., located at 1400 E Business Center Drive, Ste. 108, Mount Prospect, IL 60056, USA. Contact can be made via the toll-free number 1-800-291-8838.
Conclusion
Good Earth Lighting provides a comprehensive range of LED lighting solutions that combine energy efficiency, durability, and smart functionality. Whether you are installing a high-performance floodlight for outdoor security or integrating smart LED panels and strips for interior lighting, the installation process is designed to be user-friendly and safe. By following the manufacturer’s instructions, using the correct tools and accessories, and ensuring compatibility with smart systems, users can achieve optimal performance from their Good Earth lighting products. For further assistance, detailed instruction manuals, replacement parts, and customer support are available through the company’s official resources.