Introduction
Brizo offers a range of advanced shower systems designed for performance, safety, and durability. For professionals and experienced users, the installation and maintenance of these systems require adherence to detailed manufacturer instructions. This article provides a technical overview of the Brizo T84613 Single Function Body Spray and the T75580-BL TempAssure Thermostatic Valve, both of which feature specialized installation procedures and safety protocols. The information is derived exclusively from official Brizo product manuals and technical documentation to ensure accuracy and reliability for U.S.-based users.
Installation of the Brizo T84613 Single Function Body Spray
Pre-Installation Requirements
Before beginning the installation process, it is essential to carefully review all provided instructions. The Brizo T84613 Single Function Body Spray, model HYDRACHOICETM MAX BODY SPRAY TRIM, requires precise handling to ensure proper function and to avoid potential damage or personal injury.
- Read all instructions prior to installation.
- Ensure all installation tools and materials are available:
- Test cap/plaster guard (1)
- 100% plumbing silicone/adhesive (4)
- Trim module (2)
- Installation tool (3)
- Escutcheon (5)
Failure to follow these guidelines may result in improper installation, which could lead to product malfunction or safety hazards.
Step-by-Step Installation Procedure
Remove the Test Cap/Plaster Guard
- Begin by removing the test cap or plaster guard (1) from the previously installed rough body.
- Store the removed component for potential future use.
Apply Adhesive to the Trim Module
- Apply a small amount of 100% plumbing silicone/adhesive (4) to the back outer edge of the trim module (2).
- This adhesive ensures a secure fit and prevents leaks.
Insert and Secure the Trim Module
- Carefully insert the trim module into the rough body.
- Use the provided installation tool (3) to tighten the module.
- It is important to tighten the module only by hand—finger-tight is sufficient. Over-tightening may cause damage to the trim or internal components.
Clean Excess Adhesive
- After securing the trim, wipe away any excess silicone or adhesive from the surrounding area.
- This step ensures a clean, professional finish and prevents future cleaning challenges.
Install the Escutcheon
- Apply a small amount of 100% plumbing silicone/adhesive (4) to the flat surface of the escutcheon (5).
- Leave a 1/4 inch gap on either side of the weep hole (6) to allow for proper water drainage.
- Align the escutcheon with the retention tabs on the trim module (2), ensuring the weep hole is oriented downward.
- Press firmly until the escutcheon snaps into place.
Final Checks
- Inspect the installation for any visible gaps or misalignments.
- Verify that all components are securely attached and that the weep hole is unobstructed.
Maintenance and Cleaning
The Brizo T84613 is designed for easy maintenance. Over time, the filter screen (7) may become clogged with debris, requiring periodic cleaning. The maintenance process is as follows:
Remove the Escutcheon
- Gently pry the escutcheon (5) off, starting at the weep hole located at the bottom.
Remove the Trim Module
- Use the provided installation tool (3) to remove the trim module (2).
Clean the Filter Screen
- Carefully remove the filter screen (7) and flush it with water until it is free of debris.
- Reassemble the components in reverse order to restore the system to full functionality.
Regular cleaning and maintenance help ensure the longevity and performance of the Brizo T84613 system.
Installation of the Brizo T75580-BL TempAssure Thermostatic Valve
Pre-Installation Requirements
The Brizo T75580-BL TempAssure Thermostatic Valve is a critical component for maintaining consistent water temperature in shower systems. Due to its specialized function, the installation process requires careful attention to detail and adherence to the manufacturer's instructions. The valve includes a 3-function diverter and must be installed by a qualified professional to ensure safety and optimal performance.
- Read all installation instructions carefully before beginning the process.
- Ensure that the water heater and inlet temperature settings are stable and correct.
- Verify that the installation environment meets the required specifications for plumbing and electrical systems.
- Use only genuine Brizo replacement parts and tools as recommended in the documentation.
Failure to properly install or adjust the TempAssure valve may result in hot water burns or extreme temperature fluctuations during use.
Step-by-Step Installation Procedure
Prepare the Installation Site
- Ensure that the rough-in body (R75000) is correctly installed and accessible.
- Turn off the water supply to the valve to prevent accidental flow during installation.
Remove Protective Components
- Remove the cover (1), bonnet nuts (2), and test caps (3) from the rough-in body.
- Place a small bucket or container over the front of the valve body to collect any water or debris that may be flushed out during this process.
Flush the Supply Lines
- Slowly open the water supply to flush any debris from the supply lines.
- Once the lines are clean, turn the water supply back off.
Insert the Cartridge
- Rotate the valve cartridge (1) so that the word “UP” (2) appears on the top.
- The “H” side should be aligned with the hot water supply, and the “C” side with the cold water supply.
- Apply silicone lube to the three o-rings (3) to facilitate smooth installation.
- Insert the cartridge into the valve body, ensuring that the keys on the body are fully engaged with the corresponding slots.
- A light coating of plumbers' grease on the o-rings may further aid in assembly.
Secure the Cartridge
- Once the cartridge is fully inserted, verify that it is seated correctly and that all components are aligned.
- Reinstall the bonnet nuts and cover to complete the assembly.
Adjust the Temperature Knob
- The temperature knob must be manually adjusted to ensure a safe and consistent water temperature.
- The installer must set the knob according to the current inlet and water heater temperatures.
- It is important to note that the valve does not automatically adjust for changes in inlet temperature or pressure.
- Seasonal changes or modifications to the water heater may require readjustment of the valve.
Apply Warning Labels
- After the installation is complete, apply the caution and warning labels as specified in the documentation.
- These labels must be clearly visible to the end user and must include the installer’s name, company, and the date of the adjustment.
- Place one label on the back of the nearest cabinet door and another on the water heater.
Final Inspection
- Test the valve to ensure that it maintains a stable water temperature under varying pressure conditions.
- Monitor the performance during the initial days of use and make any necessary adjustments.
Safety and Maintenance Considerations
Importance of Professional Installation
Brizo strongly advises that all installations, particularly those involving thermostatic valves and body sprays, be performed by a licensed plumber or trained professional. The complexity of these systems and the potential risks associated with improper installation necessitate the use of expert knowledge and experience. Attempting installation without the appropriate skills may result in system failure, personal injury, or voiding of the warranty.
Maintenance Requirements
Both the Brizo T84613 and the T75580-BL require regular maintenance to ensure continued performance and safety. Users should inspect the systems periodically for signs of wear, leakage, or clogging. Cleaning the filter screens and checking for loose components are essential tasks that should be performed as part of routine maintenance.
Warranty and Support
Brizo provides a limited warranty on its products, which covers defects in materials and workmanship under normal use. However, the warranty is non-transferable and does not apply to products purchased from unauthorized sellers. Additionally, labor costs associated with installation, repair, or replacement are not covered under the warranty.
To register a product and access technical documentation, users are encouraged to visit the Brizo website at www.brizo.com. For any questions or concerns regarding installation, adjustment, or maintenance, users may contact Brizo customer support at 1-877-345-BRIZO (2749).
Conclusion
The Brizo T84613 Single Function Body Spray and the T75580-BL TempAssure Thermostatic Valve are advanced plumbing solutions designed for precision, durability, and safety. Proper installation and maintenance are essential to achieving optimal performance and ensuring user safety. By following the detailed instructions provided in the manufacturer's documentation, professionals and experienced users can confidently install and maintain these systems. Brizo’s commitment to quality and customer support further enhances the reliability of these products, making them suitable for a wide range of residential and commercial applications.